Teradek Beam is an H.264 video encoder, capable of sending high quality video at bit rates of up to 30Mbps. Beam works in the 5GHz band and can transmit up to 760m with just 2 frames delay. With 3G-SDI input and the choice of V-mount or AB mount, Beam integrates seamlessly into most cameras. It also includes OLED screen for quick setup, LAN port, RS-422 for camera control and IFB. Beam uses the RTSP and MPEG-TS protocols to broadcast over the Internet to a Beam decoder or to any computer. The Beam decoder can also act as an RTSP server. Features: Bi-directional IFB OLED screen for configuration and monitoring. Transmission up to 4 receivers over Wi-Fi Includes case Transmitter and receiver with V-mount
Video Compression: H.264 Baseline Profile Level 4.2 with de-interlacing
System Latency: 90 – 110 millisecond delay between Transmitter and Receiver
Wireless range: 2500ft +- 200ft
Digital Video In/Out: SD-SDI, HD-SDI, 3G-SDI
Video Port TX: SDI input and looped Output, RX: SDI output
Supported Video Resolutions:
SMPTE244; 480i59.94 (NTSC), 480i60 (861-D) IEC61179-5; 576i50 (PAL)
SMPTE 296M; 720p23.98, 720p24, 720p25, 720p29.97, 720p30, 720p50, 720p59.94, 720p60
SMPTE 274M; 1080i50, 1080i59.94, 1080i60, 1080PsF23.98,1080PsF24, 1080PsF25, 1080PsF29.97, 1080PsF30, 1080p23.98, 1080p24, 1080p25, 1080p29.97, 1080p30, 1080p50, 1080p59.94, 1080p60
SDI Compliance:
SMPTE 259M BI.656; SDTV Digital Signal/Data Serial Digital Interface
SMPTE 292M BT.1120; 1.5Gb/s Signal/Data Serial Digital Interface
SMPTE 425M (option); 3Gbis Signal/Data Serial Digital Interface
SMPTE 299M; 16bit Digital Audio Format for SMPTE 292M
SMPTE 352M, Video Payload Identification for Digital Interfaces
Bitrate: RTSP Server; Up to 30Mbps; MPEG2-TS Server; Up to 15Mbps
Main Digital Audio In/Out: TX/RX; SDI embedded audio: 48kHz 16-bit stereo linear PCM
Main Analog Audio Out: RX; 48kHz 16-bit stereo linear PCM with mini stereo phone output jack
Talk-Back Analog Audio In/Out: RX/TX; 8kHz 16-bit stereo linear PCM with mini stereo phone input/output jack
Radio Power: Aggregate Power: 150mW (22dBm), 50mW (17dBm)/antenna
Radio Standard: IEEE 802.11a/n: OFDM
Frequencies: U-NII-1 (5.15-5.25 GHz), U-NII-3 (5.725-5.85 GHz)
Antenna: 3T x 3R MIMO, 3 antennas per WiMi6200TW/W1Mi6200RW
Security: 802.1x, 802,11i, WPA2, WPA and WEP 64/128 TKIP 128bit AES
WPS: Wireless Protected Setup for easy set up and security configuration
Ethernet LAN: 10/100 BASE-TX, RJ-45 jack
Multicast: WiFi: Up to 4 Receivers; LAN: No limit on number of receivers
External Control: Full duplex RS422 serial port
USB: Factory reset, IP configuration or firmware upgrade without PC
Power Input/Consumption: DC 6.6V-16V, 12 Watt
Dimensions (H x W x D) (mm): 170 x 105 x 28 each board assembly (TX or RX)
Weight (g): 140g each board assembly (TX or RX)
Operating Temperature: 0 deg C to 50 deg C
